View LTL-42NGRH183_8973595.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release bns-od-fc001/a4 lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL-42NGRH183 spec no. :ds20-2017-0019effective date: 02/15/2017 revision: -
1 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 through hole lamp LTL-42NGRH183 rev description by date p001 preliminary specification (rdr-20160432-01) ja vy h. 04/13/2016 p002 add cbi bin code javy h. 08/30/2016 above data for pd and customer tracking only - upload on opnc system mike chang 2/10/2017
2 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 1. description cbi (circuit board indicator) is a black plastic ri ght angle holder (housing) which mates with lite-on led lamps. lite-on cbi is available in a wide variety of packages, including top-view (spacer) or right angle and horizontal or vertical arrays which is stackable and easy to assembly. 1. 1. features designed for ease in circuit board assembly black case enhance contrast ratio solid state light source low power consumption & high efficiency lead free product & rohs compliant t-1 lamp: led emitted colors are 569nm green (yellow green) and 625nm red chip. 1.2. applications communication computer consumer home appliance 2. outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted . 3. the holder (housing) material is plastic / black. 4. led1 is green (yellow green) color with green diffu sed lens; led2 is red color with red diffused lens. 5. specifications are subject to change without notice .
3 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 3. absolute maximum ratings at ta=25c parameter green (yellow green) red unit power dissipation 52 52 mw peak forward current (duty cycle Q 1/10, pulse width Q 0.1ms) 60 60 ma dc forward current 20 20 ma operating temperature range -30 to + 85 storage temperature range -40 to + 100 lead soldering temperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. electrical / optical characteristics at ta=25c parameter symbol color min. typ. max. unit test condition luminous intensity iv green red 8.7 3.8 15 14 29 30 mcd if = 10ma note 1,3 viewing angle 2 1/2 green red 70 70 deg note 2 (fig.6) peak emission wavelength p green red 572 630 nm measurement @peak (fig.1) dominant wavelength d green red 566 613.5 569 625 574 633 nm if = 10ma note 4 spectral line half-width ? green red 15 20 nm forward voltage vf green red 2.0 2.0 2.5 2.5 v if = 10ma reverse current ir green red - 100 100 a vr = 5v, note 5 note: 1. luminous intensity is measured with a light sens or and filter combination that approximates the cie eye-response curve. 2. 1/2 is the off-axis angle at which the luminous int ensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 5. reverse voltage (vr) condition is applied for ir test only. the device is not designed for reverse operation.
4 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 5. typical electrical / optical characteristics cur ves (25 c ambient temperature unless otherwise noted)
5 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 6. packing specification
6 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 7. bin table specification for reference lamp for green color luminous intensity, unit: mcd, if=10ma (green) iv bin code min. max. l1 19 29 l2 12.6 19 l3 8.7 12.6 note: tolerance of each bin limit is 30% dominant wavelength, unit: nm, if=10ma (green) hue bin code min. max. h09 572.0 574.0 h08 570.0 572.0 h07 568.0 570.0 h06 566.0 568.0 note : tolerance of each bin limit is 1nm lamp for red color luminous intensity, unit: mcd, if=10ma (red) iv bin code min. max. 3st 3.8 6.5 3uv 6.5 11 3wx 11 18 3yz 18 30 note: tolerance of each bin limit is 30% dominant wavelength, unit :nm, if=10ma (red) hue bin code min. max. h27 613.5 617.0 h28 617.0 621.0 h29 621.0 625.0 h30 625.0 629.0 h31 629.0 633.0 note : tolerance of each bin limit is 1nm
7 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 cbi ranks cbi bin code ltl-42ngy8d (green) ltl-42new8d (red) a l3h06, l3h07, l3h08, l3h09 3sth27, 3sth28, 3sth29, 3sth30, 3sth31 3uvh27, 3uvh28, 3uvh29, 3uvh30, 3uvh31, 3wxh27, 3wxh28, 3wxh29, 3wxh30, 3wxh31 b l2h06, l2h07, l2h08, l2h09 3sth27, 3sth28, 3sth29, 3sth30, 3sth31, 3uvh27, 3uvh28, 3uvh29, 3uvh30, 3uvh31, 3wxh27, 3wxh28, 3wxh29, 3wxh30, 3wxh31 c l1h06, l1h07, l1h08, l1h09 3sth27, 3sth28, 3sth29, 3sth30, 3sth31, 3uvh27, 3uvh28, 3uvh29, 3uvh30, 3uvh31, 3wxh27, 3wxh28, 3wxh29, 3wxh30, 3wxh31 note: tolerance of each iv bin limit is 30% tolerance of each hue bin limit is 1nm
8 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 8. cautions 8.1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 8.2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is re commended that leds out of their original packaging are used withi n three months. for extended storage out of their o riginal packaging, it is recommended that the leds be stored in a sealed con tainer with appropriate desiccant or in desiccators with nitrogen ambient. 8.3. cleaning use alcohol-based cleaning solvents such as isoprop yl alcohol to clean the leds if necessary. 8.4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do no t use the base of the lead frame as a fulcrum during forming. lead formin g must be done before soldering, at normal temperat ure. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 8.5. soldering when soldering, leave a minimum of 2mm clearance fr om the base of the lens/holder to the soldering poi nt. dipping the lens/holder into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions: soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2mm from the base of the epoxy bulb pre-heat pre-heat time solder wave soldering time dipping position 120c max. 100 seconds max. 260c max. 5 seconds max. no lower than 2mm from the base of the epoxy bulb note: excessive soldering temperature and/or time m ight result in deformation of the led lens or catas trophic failure of the led. ir reflow is not suitable process for through-hole type led lamp product. max temperature of wave sold ering is not means that holders hdt/melting temperature. 8.6. drive method an led is a current-operated device. in order to en sure intensity uniformity on multiple leds connecte d in parallel in an application, it is recommended that a current limit ing resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model (a) circuit model (b) led led (a) recommended circuit (b) the brightness of each led might appear differe nt due to the differences in the i-v characteristic s of those leds.
9 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 8.7. esd (electrostatic discharge) static electricity or power surge will damage the l ed. suggestions to prevent esd damage: use a conductive wrist band or anti- electrostatic glove when handling these leds all devices, equipment, and machinery must be prop erly grounded work tables, storage racks, etc. should be properl y grounded use ion blower to neutralize the static charge whi ch might have built up on surface of the leds plast ic lens as a result of friction between leds during st orage and handing suggested checking list: training and certification 8.7.1.1. everyone working in a static-safe area is esd-certified? 8.7.1.2. training records kept and re-certific ation dates monitored? static-safe workstation & work areas 8.7.2.1. static-safe workstation or work-areas have esd signs? 8.7.2.2. all surfaces and objects at all stati c-safe workstation and within 1 ft measure less tha n 100v? 8.7.2.3. all ionizer activated, positioned toward s the units? 8.7.2.4. each work surface mats grounding is g ood? personnel grounding 8.7.3.1. every person (including visitors) han dling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 8.7.3.1. if conductive footwear used, conductive flooring also present where operator stand or walk? 8.7.3.2. garments, hairs or anything closer th an 1 ft to esd items measure less than 100v*? 8.7.3.3. every wrist strap or heel strap/condu ctive shoes checked daily and result recorded for a ll dls? 8.7.3.4. all wrist strap or heel strap checker s calibration up to date? note: *50v for blue led. device handling 8.7.4.1. every esds items identified by eia-47 1 labels on item or packaging? 8.7.4.2. all esds items completely inside prop erly closed static-shielding containers when not at static-safe workstation? 8.7.4.3. no static charge generators (e.g. pla stics) inside shielding containers with esds items? 8.7.4.4. all flexible conductive and dissipati ve package materials inspected before reuse or recy cle? others 8.7.5.1. audit result reported to entity esd co ntrol coordinator? 8.7.5.2. corrective action from previous audit s completed? 8.7.5.3. are audit records complete and on file ?
10 / 10 part no. : ltl - 42n g r h183 bns-od-fc002/a4 through hole lamp LTL-42NGRH183 9. reliability test classification test item test condition sample size reference standard endurance test operation life ta = under room temperature if = per datasheet maximum drive current test time= 1000hrs 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1026 (1995) mil-std-883g:1005 (2006) high temperature high humidity storage ta = 60c rh = 90% test time= 240hrs 22 pcs (cl=90%; ltpd=10%) mil-std-202g:103b (2002) jeita ed-4701:100 103 (2001) high temperature storage ta= 105 5c test time= 1000hrs 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1031 (1995) mil-std-883g:1008 (2006) jeita ed-4701:200 201 (2001) low temperature storage ta= -55 5c test time= 1000hrs 22 pcs (cl=90%; ltpd=10%) jeita ed-4701:200 202 (2001) environmental test temperature cycling 100c 25c -40c 25c 30mins 5mins 30mins 5mins 30 cycles 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1051 (1995) mil-std-883g:1010 (2006) jeita ed-4701:100 105 (2001) jesd22-a104c (2005) thermal shock 100 5c -30c 5c 15mins 15mins 30 cycles (<20 secs transfer) 22 pcs (cl=90%; ltpd=10%) mil-std-750d:1056 (1995) mil-std-883g:1011 (2006) mil-std-202g:107g (2002) jesd22-a106b (2004) solder resistance t.sol = 260 5c dwell time= 101 seconds 3mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2031(1995) jeita ed-4701: 300 302 (2001) solderability t. sol = 245 5c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil-std-750d:2026 (1995) mil-std-883g:2003 (2006) mil-std-202g:208h (2002) ipc/eia j-std-002 (2004) soldering iron t. sol = 350 5c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil-std-202g:208h (2002) jeita ed-4701:300 302 (2001) 10. others the appearance and specifications of the produ ct may be modified for improvement, without prior n otice.

▲Up To Search▲

Price & Availability of LTL-42NGRH183

	To Download LTL-42NGRH183 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .